Tutorial: Envelope Cushion Back with Buttons and Binding

I began following the English Country Garden QAL in February 2021. I did intend to make all nine blocks and create the quilt-as-you-go quilt top… But best intentions and all that…I’ve got to the back end of 2021 with just four of the blocks completed. I enjoyed learning more about EPP and applique by making the blocks and also enjoyed having a slow stitching project to turn to but now I’ve decided it’s time for me to draw my involvement in the QAL to close. I’ll be making use of the completed blocks rather than consigning the project to the UFO Cupboard of Shame!

I’ve trimmed the blocks to 18½” square to make four new cushion (pillow) covers to replace the rather worn patchwork covers we’ve been using in our living room for the past 10 years or more.

I hope sharing the process I’m using to make cushion covers from these quilted patchwork blocks will be a useful guide should you decide to do something similar 🙂

Materials

  • One 18½” quilted patchwork square*
  • Cushion Back Fabric: cut two 18½” x 15″ rectangles
  • Medium weight interfacing: cut two 17½” x 2-5/8″ rectangles
  • Two 1″ buttons
  • Double fold binding: cut two Width of Fabric 2¼” strips to make approximately 84″ of binding. Sew strips together and press in half lengthways
  • 18″ x 18″ pillow form.

*I like my cushions squishy. If you prefer a firmer, tighter fit then cut your square to 18″ and the Cushion Back Rectangles to 18″ x 15″.

Equipment

  • Sewing machine with facility to make button holes
  • Rotary cutting tools
  • Pins and/or binding clips

Step One: Preparing Buttonhole Plackets

  • Place a Cushion Back Rectangle wrong side up on an ironing surface. Press a crease 3″ down from a long edge of the rectangle. Open out the rectangle.
  • Position an interfacing rectangle along the crease – there will be approximately ½” fabric exposed at either end and approx. ¼” seam allowance along the top of the rectangle.

 

  • Adhere the interfacing in place as per manufacturers instructions.
  • Fold and press the seam allowance over the edge of the interfacing Diagram 1.
  • Fold the interfacing flap to the back of the rectangle and pin in place.
  • Top stitch 1/8″ along the top edge and 1/8″ inside the seam allowance to secure the placket Diagram 2. Now measures 18½” x 12″ (18″ x 12 if making the tighter fitting version).
View of wrong side of a Back Rectangle with top stitching completed.
  • Repeat to prepare the second Cushion Back Rectangle.

Step Two: Make Buttonholes and Attach Buttons

  • Fold a Cushion Back Rectangle in half on the placket edge and make a crease to mark the centre.
  • Lay the Cushion Back Rectangle face up on a flat surface.

  • Measure 2½” away from the centre crease and make an erasable mark starting ¾” above the top stitching that secures the placket seam.
  • Repeat to measure and mark a buttonhole 2½” away from the other side of the centre crease.
  • Make vertical button holes using the marks as guides.
  • Place the Button Hole Placket, face up, directly on top of the placket of the other Backing Fabric rectangle (also face up).
  • Make a mark through each buttonhole onto the placket below to position the buttons.
  • Attach buttons.

Step Three: Attach Cushion Back Rectangles and Binding to Cushion Front

  • Lay the Cushion Front right side down on a flat surface.
  • Button the two Backing Rectangles together and pin placket ends so plackets are lying directly on top of each other.
  • With Cushion Back face up, place one 18½” edge directly on top of a Cushion front edge. Pin in place.

  • Carefully smooth the Backing over the Front. Pin in place. There will be a strip of excess Backing fabric along one edge.

  • Flip the pinned pieces over so the the Cushion Front is uppermost. Use a rotary cutter to remove the excess Backing Fabric.

  • Pin the binding raw edge to raw edge around the Cushion Front*. Start on an edge that does not have exposed Placket ends.
  • Stitch the binding in place using a ¼” seam in the usual way. Take care not to accidently flip the placket pieces as you stitch.
  • Hand stitch the binding to the back of the cushion cover.

*If you would rather machine stitch both edges of the binding then first stitch the binding raw edges to the Cushion Back before flipping the binding round and machine stitching it to the front of the cushion cover.

I hope this tutorial is useful. Any questions or suggestions do get in touch with me using the comments box at the bottom of this page. If you are interested in reading more of my tutorials you can find them by using the ‘Tutorials’ tab in the header 🙂 . I’ve also published several patterns including the I-Spy Shadow Quilt pattern, these can be bought as PDF downloads from my Etsy Shop.

Linking with Kelly for Needle & Thread Thursday. Kelly has been busy hanging lights outside her house in time for the Holiday Season but has had time to create a gallery of quilts from last weeks linkup.

Allison

 

2 thoughts on “Tutorial: Envelope Cushion Back with Buttons and Binding

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Newsletter Signup

Subscribe to the newsletter to receive: 

  • Links into the Worldwide Quilting Community.
  • Links to tutorials and patterns.
  • And be the first to see new listings in my Folksy and Etsy shops 
%d bloggers like this: